How to Install a Bathtub ( Guide).
How to Install a Bathtub ( Guide).
Blog Article
What're your thoughts concerning How to Install a Bathtub Yourself?
Installing a tub isn't exactly brain surgery, but it does need solid plumbing, woodworking, and often, tiling abilities. Changing an old tub with a brand-new one is also a reasonably difficult job. If the old bathtub is conveniently available, the job can relocate quickly; if you need to open up a wall to eliminate the old bathtub and position the brand-new bath tub, the task is much harder. In either situation, the task is within a residence handyman's skills, although you will require an assistant to move out the old tub as well as embeded in the brand-new one. Make certain you have actually qualified yourself for the task and also are comfortable attempting it. Rather than employing a specialist to take control of a halfway-completed project, it is much better to consider employing one before you begin. Chances are you may need an expert plumber to make tube connections.
This short article will assist you set up a new tub in your shower room if you have actually currently gotten a brand-new bathtub as well as don't need to change the arrangement of your previous supply of water pipes.
Your tools and product list need to consist of the following:
Removing Old Taps
If you require to change old faucets with brand-new ones as a part of your setup, then the first thing you should do is disconnect the water supply. After doing so, activate the faucets to drain pipes any type of water remaining in the system. The process of removing the existing faucets can be fairly troublesome because of the restricted access that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been eliminated, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the faucets have actually been eliminated, the holes in the bath/basin will have to be cleansed of any type of old sealing compound.
Prior to going on to fit the new taps, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Taps
If the tails of the brand-new faucets are plastic, then you will require a plastic port to prevent damage to the string. One end of the port fits on the plastic tail of the tap and also the various other end offers a link to the current supply pipes.
If you require to fit a monobloc, after that you will call for minimizing couplers, which links the 10mm pipe of the monobloc to the common 15mm supply pipe.
Next, place the tap in the placing opening in the bath/basin guaranteeing that the washing machines remain in place in between the tap and also the sink. Safeguard the faucet in place with the manufacturer given backnut. When the faucet is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be attached by utilizing corrugated copper piping or with normal faucet connectors. The previous type must be attached to the tap finishes first, tightening up only by hand. The supply pipelines can later be attached to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Tub
Using both wooden boards under its feet, place the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the area of the boards instead of concentrating all the weight onto 4 tiny points.
The following objective is to ensure that the bath tub is leveled all round. This can be accomplished by checking the level as well as adjusting the feet on the tub until the level checks out level.
To set up taps, fit all-time low of the furthest adaptable tap adapter to the proper supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water supply as well as check all joints and also brand-new pipework for leaks and also tighten them if required. Load the tub as well as additionally inspect the overflow electrical outlet as well as the regular outlet for leakages.
Finally, deal with the bath paneling as defined in the producer's user's manual. Tiling and securing around the bathtub must wait until the tub has actually been utilized at the very least once as this will certainly resolve it into its last position.
Getting ready for the Installment
First of all, the sustaining frame provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is very important to see to it that if the tap includes a plastic washing machine, it is fitted between the bath and also the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the taps device to prevent strain on the tub.
Fit the adaptable tap ports to the bottom of both faucets using 2 nuts as well as olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet via the hole in the bath. Utilize the nut provided by the supplier to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bathroom. Make sure you use all of the supplied washing machines.
Attach the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom must currently prepare to be suited its final setting.
Tiling Around the Tub
In the area where the bath meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate sufficient to split a stiff seal, triggering the water to permeate the wall between the bath and also the tiling, bring about difficulties with moisture as well as possible leaks to the ceiling below.
You can pick from a selection of coloured sealers to blend in your fixtures and installations. They are marketed in tubes as well as cartridges, and are capable of securing voids as much as a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with spins of soaked newspaper or soft rope. Bear in mind to always fill the bath tub with water before securing, to permit the motion experienced when the bathtub remains in use. The sealer can break fairly early if you do not take into account this activity before sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and reduce to dimension, are likewise easily readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof sticky and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Do you enjoy reading up on How to Install a Bathtub Yourself? Put a remark down the page. We will be delighted to find out your feelings about this posting. Hoping to see you back again before long. If you liked our post kindly be sure to pass it around. Thank-you for your time invested reading it.
Set An Appointment Report this page